氣體增壓泵的正確選型
為了使訂購的
氣體增壓泵處于最佳工作狀態，在選擇
氣體增壓泵泵時必須要從多方面進行考慮：In order to make the gas booster pump ordered in the best working condition, in the choice of gas booster pump must be to consider many aspects: 1.工作壓力和流量1 working pressure and flow
氣體增壓泵和動力單元的工作壓力參照驅動氣壓為0.48Mpa時泵輸出壓力和流量。如果泵的最大輸出壓力大于所需的工作壓力，這就要考慮安全措施。對于最大輸出壓力，請參照產品目錄中的“靜態下驅動氣壓力和輸出液壓近似比率表”。動力單元的選型與泵一致。Gas booster pump and a power unit of work pressure according to the driving pressure of 0.48Mpa pump output pressure and flow. If the maximum pump output pressure is greater than the required working pressure, it is necessary to consider the safety measures. For maximum output pressure, please refer to the catalogue of "static driving gas pressure and output hydraulic approximation ratio table". Consistent selection and pump power unit. 2.驅動氣體的壓力和流量 The 2 driving gas pressure and flow
氣體增壓泵和動力單元在連續工作時使用的驅動氣壓不超過0.69Mpa，在間歇工作時可達到1.03Mpa。在最佳性能狀態時氣動泵的耗氣量，請參照所需驅動氣體流量表。The driving pressure gas booster pump and a power unit used in continuous operation shall not exceed 0.69Mpa, the intermittent work can reach 1.03Mpa. In the best performance state aerodynamic consumption of air pump, please refer to the driving gas flow meter. 3.輸送液體介質3 the delivery of liquid medium
氣體增壓泵http://www.rizhaowx.com/輸送的液體介質是
氣動增壓泵的選型中著重考慮的部分。液壓部分的材質和液壓密封圈是由輸送的液體介質所決定的。泵可用油、水和大多數液體介質。標準泵的主要液壓密封圈是丁橡膠和聚氨酯，單向閥座采用特氟龍密封。其它密封材料包括碳氟化合物和亞乙基丙烯，這些密封材料主要用于輸送的特殊介質。請向工廠或當?shù)氐姆咒N商咨詢密封材料選型。Liquid gas booster pump is considered in the selection of pneumatic booster pump parts. The material and the hydraulic part of the sealing ring is determined by the liquid medium conveying. Pump available oil, water and most liquid medium. The main hydraulic pump sealing ring is standard chloroprene rubber and polyurethane, one-way valve seat with Teflon seal. Other sealing materials including fluorocarbon and ethylene propylene, the sealing material is mainly used for special medium conveying. Please refer to the factory or a local distributor for sealing material selection. 4.
氣體增壓泵可接受的體積和重量對于某些的應用，
氣體增壓泵和動力單元的外形尺寸和重量也要重點考慮4 gas booster pump acceptable volume and weight for some applications, the size and weight of gas booster pump and a power unit should also be considered
當前位置：
首頁 >>
公司動態 >>
行業資訊
發布時間：
2014-09-06
上一篇：
淺析爆破試驗臺壓力容器
下一篇：
爆破試驗臺的工藝技術